UAV Shop
 
 
 
 

KDE XF 95A HVC OPTO Brushless Multirotor ESC

KDE XF 95A HVC OPTO Brushless MultiRotor ESC

Brand: KDE

SKU: 12304

The new UAS HVC series brings to life the next generation of technology for UAS and multirotor operation, including an Aluminum 6061-T6 case for cool running temperatures and rugged construction, allowing the ESCs to be used in a wide range of harsh environments and commercial/industrial applications.  The new series also comes pre-loaded with the latest production firmware, including these new, market leading technologies:

  • Regenerative Braking– active braking during motor deceleration phase, providing instantaneous response to the flight controller commands and matched response to acceleration profiles (less “float” during flight)
  • Temperature Controlled Synchronous Rectification– new proprietary algorithm for smooth running motors at low throttle and improved, faster response under high peak loads; all while significantly increasing flight time efficiency and reducing operating temperatures (also termed "active freewheeling")
  • Dynamic Timing and Startup Power– optimally tuned for smooth and precision controlled startup throughout the full range of UAS Brushless Motors (no hesitation, stuttering, or response lag)
  • Increased Drive and Throttle Frequency Resolution – high accuracy, linear throttle response throughout full range of operation control
  • Motor Synchronization – factory calibrated ESCs for consistent throttle control and frequency matched startup protocols

The UAS HVC series is compatible with 3S - 12S LiPo (55V Max) power systems, allowing for the next level of performance and efficiency for your UAS and multirotor applications.  In addition, the UAS HVC series includes active anti-spark circuitry, protecting the integrity and lifespan of the critical connectors upon each initial plug-in and system power-up

The series is tuned and optimized for the KDE Direct UAS multirotor Brushless Motor Series, for simple plug-and-play operation. No additional throttle calibration is required for most applications and settings are factory programmed

ESCs include 200°C, 12 AWG silicone wire power leads and 13 AWG silicone wire motor leads with dual 6.5mm and 4.0mm 24K matching Bullet Connectors

Includes:

  • Two (2) KDE Direct XF 4.0mm 24K Bullet Connectors (Pair, KDEXF-BC40)
  • Two (2) KDE Direct XF 6.5mm 24K Bullet Connectors (Pair, KDEXF-BC65)

Full Specifications:

Refresh Rate600 Hz (50 - 600Hz Adaptive)
Maximum Peak Current165 A (5 s)
Maximum Peak Power7,330 W (5 s)
Maximum Continuous Current*95+ A (180 s)
Maximum Continuous Power*4,220+ W (180 s)
Maximum Efficiency> 98%
Voltage Range11.1 V (3S) - 50.4 V (12S)
Internal BECNone (Opto-Isolation)
Maximum RPM360,000 rpm (2-Pole)
PWM RateAdaptive Dynamic Algorithm
Advance Timing22° - 30° Dynamic Algorithm
ESC Size37 mm (W) x 82 mm (L)
ESC Weight84 g (110 g with Wires/Bullets)
Power Leads12 AWG, 200°C
Motor Leads13 AWG, 200°C
ESC Control Lead22 AWG, 3-Wire JR (W-R-B)
ESC Programming Lead22 AWG, 3-Wire JR (O-R-B)
Power Connects4.0 / 6.5 mm Matched Pair
Motor Connects4.0 mm Female

* ESC requires consistent airflow (5 mph or greater)across the heatsink to maintain maximum continuous current and power ratings during operation, specified at full load condition (100% throttle). Increasing airflow or adding additional cooling can further increase the capabilities of the controller and extend the lifespan of the critical internal components

Full Specifications:

Refresh Rate600 Hz (50 - 600Hz Adaptive)
Maximum Peak Current165 A (5 s)
Maximum Peak Power7,330 W (5 s)
Maximum Continuous Current*95+ A (180 s)
Maximum Continuous Power*4,220+ W (180 s)
Maximum Efficiency> 98%
Voltage Range11.1 V (3S) - 50.4 V (12S)
Internal BECNone (Opto-Isolation)
Maximum RPM360,000 rpm (2-Pole)
PWM RateAdaptive Dynamic Algorithm
Advance Timing22° - 30° Dynamic Algorithm
ESC Size37 mm (W) x 82 mm (L)
ESC Weight84 g (110 g with Wires/Bullets)
Power Leads12 AWG, 200°C
Motor Leads13 AWG, 200°C
ESC Control Lead22 AWG, 3-Wire JR (W-R-B)
ESC Programming Lead22 AWG, 3-Wire JR (O-R-B)
Power Connectsф4.0 / ф6.5 mm Matched Pair
Motor Connectsф4.0 mm Female

* ESC requires consistent airflow (5 mph or greater)across the heatsink to maintain maximum continuous current and power ratings during operation, specified at full load condition (100% throttle). Increasing airflow or adding additional cooling can further increase the capabilities of the controller and extend the lifespan of the critical internal components

Qty
 
 

 

You may also like